Industrial coatings, thermal coating | supertherm, hpc, hsc | New York, East Coast, United States

LEED

scsadmin — Sat, 25 Feb 2012 22:34:44 +0000

A Guide to Our LEED Benefits and Contributions

Introduction

The LEED Green Building Rating System (Leadership in Energy and Environmental Design) has become a de facto global standard for sustainable buildings. Emphasizing environmental responsibility, wellness, and energy efficiency, this certification system applies to all of the main aspects of green buildings: design, construction, and operation.

At Superior Coating Solutions, we fully embrace this standard. Our products are can provide our customers LEED credits across four of the five environmental categories, plus Innovation in Design, due to our use of Cradle-to-Cradle materials. The table below shows the primary benefits of our products, how they relate to the various LEED Credit Categories, and the actual LEED Points that can be achieved through their usage. Customers who utilize Superior Coating Solutions’ products gain significant contributions to their LEED rating totals, enhancing the likelihood of attaining Gold or even Platinum certification.

LEED Benefits Without the Compromise in Performance

Often, using a product with strong LEED-related benefits means that the customer must accept a compromise in product performance. Needless to say, the vendors of these products are reluctant to point out this trade-off that accompanies their LEED ratings. At Superior Coating Solutions, our products provide industry-leading performance while also delivering substantial LEED contributions. Our products excel in such areas as aesthetics and durability, while also reducing costs related to energy usage, heat consumption, and mold/mildew control. This exceptional performance, combined with the breadth of LEED advantages referenced above, is what truly distinguishes the products of Superior Coating Solutions from those of other vendors in the industry.

SCS Product Benefit

LEED Credit Category

Possible LEED Points

Comments

Enhanced Energy Performance plus Reduced Energy Demand

Energy and Atmosphere*

1-10

EA Prerequisite 2 (Minimum Energy Performance) and EA Credit 1 (Optimize Energy Performance); Exceeds AHSRAE/IESNA Standard 90.1-2007 by 10%

Noise Reduction and Improved Room Sound Quality

Environmental Quality*

1-2

EQ Credit 9 –

LEED for Schools (Acoustical Performance)

Low VOC Emissions

Environmental Quality*

1

EQ Credit 3.2 (Indoor Air Quality) and EQ Credit 4.2 (Low Emitting Materials)

Increased Thermal Comfort Through Insulation Value

Environmental Quality*

1

EQ Credit 7.1 (Thermal Comfort)

Resistance to Mold and Mildew

Environmental Quality*

1

EQ Credit 10 – LEED for Schools (Mold Prevention)

Reduce Surface Temperature of Building

Sustainable Sites*

1

SS Credit 7.2 (Heat Island Effect)

Innovative Design for Both Environmental and Health Benefits

Innovation in Design

1

ID Credit 1-1.4 (Innovation in Design)

Improved Durability of Home Interior Moisture Control

Innovation in Design

3

ID Credit 2 -

LEED for Homes (Durability Management Process)

*Denotes Environmental LEED Credit Categories

For more specific details on the LEED certification system, please go to http://www.usgbc.org/

Solutions

admin — Wed, 14 Dec 2011 19:53:58 +0000

Our Product line up offers solutions for:

Energy Savings throughout Commercial, Industrial, & Residential Facilities.

Blocking Heat Loss or Gain

Insulation of Roofing, Walls, and Equipment

Stopping Condensation

Preventing the spread of Toxic Mold

Prevention & Protection against Rusting & Corrosion

Preventing Deterioration in Harsh Environments

Chemical Protection

Underwater Protection

Concrete Protection & Sealing

Fire Proofing & Fire Resistance

Easy Graffiti Removal Without Blasting & Repainting

Reducing Costs for Refrigerated Trucks & Facilities

Energy Savings

admin — Tue, 06 Dec 2011 06:28:37 +0000

Rising energy costs coupled with greater price volatility, can wreak havoc with your bottom line. Energy efficiency has never been more important. Our heat-blocking solutions not only outperform fiberglass insulation, but can easily be applied to more difficult areas such as joints, valves, tight, or wet spaces.

Super Therm® Our flagship insulation coating that blocks heat load with an equivalent effectiveness of R-19 (6-8” of fiberglass insulation) in just 1/100^th inch. It also blocks moisture penetration, air infiltration and sound. Super Therm® is a particularly effective option for:

reflecting radiational and convective heat on roofs

blocking heat load on to substrates

many interior applications requiring enhanced insulation

HSC™ Coating - Specially designed for hot pipes or surfaces. Blocks conductive heat transfer (up to 350° F) and significantly reduces heat loss. HSC™ can also be used as an interior insulation solution for walls or under roofs to enhance or replace existing insulation.

HPC™ Coating - Specially designed to insulate and protect hot pipes or surfaces (such as on a boiler) in extreme temperature situations, up to 700° F (and higher with instructions) by effectively blocking conductive heat from leaving the surface.

Epoxotherm – Designed to insulate wet surfaces, Epoxotherm is a two- part industrial grade epoxy that combines the ceramics of Super Therm® for exceptional insulative performance. It applies directly to wet surfaces and is mold/mildew resistant.

Roof Protection/Reflective Cool Roof Options

admin — Tue, 06 Dec 2011 06:26:29 +0000

Using the proper coatings not only protects and extends the life of a roof for many years, but can provide additional insulative (energy efficient) benefits as well. Our coatings can resolve issues related to water ponding, leaks, high foot traffic, and material fatigue.

Super Therm® – The ideal reflective white roof solution. With its unique combination of 4 ceramic compounds, Super Therm® reflects 95% of solar heat (UV, Infrared, and visible light) as well as block heat load to the roof substrate. It has been proven to lose less than 1% (only .6%) of its reflectivity over 3 years and only 2% over 10 years. Under normal conditions, when applied as a system, Super Therm® has a 20+ year lifespan when used on roofing.

Enamo Grip - A particularly tough coating that is highly resistant to water, humidity, and staining, and has exceptional scuff, mark, and impact resistance. A perfect high traffic solution that can be tinted to any color or made non-skid if needed.

SP Liquid Membrane - A tough elastomeric coating that offers superior waterproof protection and can be used as a primer, as a 1-coat system, or as a top coat. It can be applied over pressure-washed substrates of TPO, EPDM, PVC, wood, concrete, or metal.

Insulation and Heat Reduction

admin — Tue, 06 Dec 2011 06:25:07 +0000

Choosing the right eco-friendly insulation coating can provide years of carefree protection and avoids many problems associated with traditional insulation. For example, when Fiberglass is exposed to as little as 1.5% humidity, it can lose up to 35% of its effectiveness. When it becomes compressed or is not tightly sealed around uneven areas, it is even less effective. Fiberglass can also pose health hazards over time as it becomes brittle and its fragments are become airborne.

Super Therm® - With its combination of 4 unique ceramic compounds, Super Therm® can effectively block heat load with the equivalent effectiveness of 6-8” of fiberglass insulation (R-19) in a coating only 10 mils (1/100^th inch) thick. It is resistant to water, mold, mildew, fire (Class A fire rating) and is certified environmentally safe by MBD LLC.

HSC™ Coating - Offers a “green”, non-flammable, non-toxic solution for blocking heat transfer on a surface up to 350° F. HSC™ can be applied to a variety of surfaces such as metal, concrete, wood, sheetrock and others. It can also be used on walls or under roofs for additional insulative protection. Unlike Fiberglass, HSC™ does not absorb moisture or lose insulation value over time.

HPC™ Coating – With its 7 non-conductive ceramic compounds, HPC™ is the ideal solution for coating surfaces exposed to extreme, sustained heat (up to 700° F). It can be applied directly to a hot surface, pipe, boiler, furnace, etc. without the need for shutdown. It can also coat and protect areas that are difficult to access such as elbows and valves which are problematic with much thicker fiberglass insulation.

Condensation

admin — Tue, 06 Dec 2011 06:23:05 +0000

Condensation on cold water pipes can cause many problems when traditional insulation or wraps are used. Just a small amount of moisture on the surface can cause corrosion under insulation (CUI) as well as cause mold problems. Our coatings cure directly to the surface, protecting it for years from corrosion, and are highly resistant to mold, mildew, and fire.

Super Therm® - As a coating with the equivalent effectiveness of 6-8” of Fiberglass insulation (R-19), Super Therm® bonds to surfaces and effectively blocks the moisture that causes corrosion. It provides years of protection and is highly resistant to mold and mildew.

HSC™ Coating – A long term solution that be applied in layers to provide additional protective insulation. HSC™ effectively blocks moisture from reaching the coated surface, protecting it from corrosion for years.

HPC™ Coating – Can be applied directly over previous coatings, provided that they are fully adhered to the surface. Effectively stops condensation in environments with significant temperature differences due to its complete surface bond.

Enamo Grip – A very tough fully waterproof top coat that can be used over the above listed coatings to give added protection against chemicals, solvents, or excessive exposure to water. Mold and mildew resistant with a 15+ year lifespan under normal conditions.

Metal Rusting and Corrosion

admin — Tue, 06 Dec 2011 06:20:47 +0000

By using the right coatings to prevent rust and corrosion you can substantially extend the useful life of your assets. In some cases where the integrity of the metal has been compromised, our coatings can actually bond to, and strengthen, rusted or corroded surfaces and prevent further degradation for many years. In addition to protecting metal surfaces, both Rust Grip® and Moist Metal Grip can be applied to concrete, masonry, or wood.

Rust Grip® – As a three-coats-in-one system, Rust Grip® acts as a primer, intermediate, and topcoat with a single application which strengthens surfaces to 6780 psi (473 bar) after 21 days. (Concrete is 3500 psi by comparison). It can be applied directly over rusted surfaces or existing paint, with no sandblasting required in most cases. This substantially cuts costs and the time required to complete a project.

Moist Metal Grip - When surfaces are too wet to apply Rust Grip®, Moist Metal Grip can be applied directly to prevent further surface corrosion. It can be used under water and is resistant to chemicals and solvents.

Asbestos/Hazardous Materials Encapsulation

admin — Tue, 06 Dec 2011 06:19:25 +0000

Safe removal of asbestos or other hazardous materials such as lead-based paint or mold can be exorbitantly expensive in addition to posing significant health risks. Proper encapsulation is a safe and highly cost effective solution for handling the abatement of toxic materials.

Rust Grip® – Rust Grip® is one of the only coatings on the market patented to safely encapsulate asbestos (patent #6,695,812) under ASTM E-1795; it can also be used to encapsulate other hazardous materials. After application to a surface, Rust Grip® hardens to 6,800 psi within 21 days. (Concrete is 3,500 psi by comparison) It effectively blocks any contact with air, moisture, or chemicals, and has also been tested as a water barrier under ASTM.

Concrete Protection

admin — Tue, 06 Dec 2011 06:18:21 +0000

Now you can extend the life, and help preserve the integrity, of concrete walls, floors, and structures. We offer various coatings that condition, strengthen, and protect concrete surfaces.

SP Interlock – An effective “conditioner” for aged or weathered concrete, SP Interlock penetrates into the pores and works to replace lost solids within a concrete surface. Use an overcoat like Enamo Grip or Rust Grip® to achieve the best results.

Rust Grip® – When rebars in concrete become weakened due to corrosion, Rust Grip® will bond within the pores of the metal to strengthen and protect it from further oxidation and rusting. Rust Grip®, when applied over concrete, is resistant to water and chemicals, and is appropriate for areas with high foot traffic.

Moist Metal Grip – Apply to surfaces that are too wet to use our other coatings. Moist Metal Grip protects and strengthens rusted metal and provides superior protection to concrete surfaces against water, chemicals, and solvents. It cures to a smooth finish that can be tinted to any color.

Enamo Grip – For a smooth, durable finish that can be tinted to any color, Enamo Grip is a waterproof sealant that is highly resistant to graffiti, chemicals, and staining. It also provides exceptional scuff, mark, and impact resistance.

Floor Protection

admin — Tue, 06 Dec 2011 06:15:40 +0000

Over time, water damage and heavy use can compromise concrete and steel flooring. Extend the useful life of your floorings and postpone expensive replacement costs using coatings that preserve and strengthen steel, concrete, and other surfaces.

Rust Grip® - As a 1-coat system, Rust Grip® bonds directly to rusted surfaces preventing further corrosion and hardens to 6,800 psi within 21 days and 12,000 psi when fully cured. It is a high performance coating for concrete, steel, and other surfaces that are exposed to the harshest environments.

Enamo Grip – An excellent choice for a durable finish sealer or topcoat that can be applied to a variety of surfaces including high traffic floors. It is fully waterproof and highly resistant to chemicals, staining, and scuffing. Enamo Grip can be tinted to any color.

Lining Kote – If you need dependable protection from the harshest chemical or solvent environments, Lining Kote is a high performance coating designed to withstand direct impact, humidity, and temperatures up to 400° F. Its two part epoxy composition provides flexible protection and can be tinted to any color.

SCS Product Benefit	LEED Credit Category	Possible LEED Points	Comments
*Enhanced Energy Performance plus Reduced Energy Demand*	Energy and Atmosphere*	1-10	EA Prerequisite 2 (Minimum Energy Performance) and EA Credit 1 (Optimize Energy Performance); Exceeds AHSRAE/IESNA Standard 90.1-2007 by 10%
*Noise Reduction and Improved Room Sound Quality*	Environmental Quality*	1-2	EQ Credit 9 – LEED for Schools (Acoustical Performance)
*Low VOC Emissions*	Environmental Quality*	1	EQ Credit 3.2 (Indoor Air Quality) and EQ Credit 4.2 (Low Emitting Materials)
*Increased Thermal Comfort Through Insulation Value*	Environmental Quality*	1	EQ Credit 7.1 (Thermal Comfort)
*Resistance to Mold and Mildew*	Environmental Quality*	1	EQ Credit 10 – LEED for Schools (Mold Prevention)
*Reduce Surface Temperature of Building*	Sustainable Sites*	1	SS Credit 7.2 (Heat Island Effect)
*Innovative Design for Both Environmental and Health Benefits*	Innovation in Design	1	ID Credit 1-1.4 (Innovation in Design)
*Improved Durability of Home Interior Moisture Control*	Innovation in Design	3	ID Credit 2 - LEED for Homes (Durability Management Process)